Please refer to the following table. TK-205K Supported Cables* Included 4ft (1.2M) TK-208K Supported Cables* Included 4ft (1.2M) TK-408K Supported Cables* Included 6ft (1.8M) TK-200 Supported Cables* TK-C06, TK-C10 & TK-C15 6 Ft.(1.83m), ...

You can use the TK-C06 (6-foot), TK-C10 (10-foot) or the TK-C15 (15-foot) cables. Follow the steps below to daisy chain your TK-802R KVM switches. KVM Cables TK-C06 TK-C10 TK-C15 Overview Diagram   Installation 1. Connect one end of the KVM cable to the...

Longer replacement cables are not available and it is recommended to use the included KVM cable.

Yes the TK-EX2 is compatible with both the TK-1602R and TK-802R KVM switches.

No, but the TK-802R is rack mountable using the included rack mount brackets.

Yes

Please refer to page 24 of the User Guide which is included on the CD-ROM that shipped with your KVM Switch; alternatively you can download it from our website....

When daisy-chaining KVMs together each KVM switch is referred to as a bank, and the bank number helps identify what KVM switch you are accessing....

You would need to reset the KVM to clear all programmed station names or for other diagnostic purposes....

The KVM Switch can be reset without disconnecting or powering down your computers either by (1) pressing down Button 1 on the front panel for 2 seconds, or by (2) the hotkey sequence ScrLk + ScrLk + End. Note that each keystroke should be followed by its next keystroke within a delay of no more than...

Console ports are used to connect your Keyboard, Video (Monitor), and Mouse for control over multiple PCs. Console ports tell us what type of connections are supported just by looking at the interfaces on the front of the KVM. Many KVM switches feature VGA (Monitor) and PS/2 (Mouse and Keyboard) con...

KVM cables are available directly from TRENDnet here.

The TK-802R doesn't come with any KVM cables other than the included daisy-chain cable. This allows users to customize their cable selection according to the network ...

To add port capacity, multiple TK-802R/TK-1602R KVM Switches can be cascaded in a daisy-chain configuration to maximize the number of connected computers up to a total of 256 computers (with 16 units of TK-1602R KVM Switches) or 128 computers (with 16 units of TK-802R KVM Switches)....

The included daisy chain cable is 0.85 m/2.8 ft.

OSD (On Screen Display) is a menu that is superimposed on your screen. On the OSD Menu, you will have a listing of the available banks and channels for selection and the currently online status of each channel. You can use it to control the KVM switch with more convenient and intuitive menu-driven o...

Make sure that your mouse is properly connected to the computer and to the KVM switch. Check that your mouse is plugged into the PS/2 mouse port and not the PS/2 keyboard port. Connect your mouse to the computer directly to verify that it is working If you are having trouble with the ...

Make sure that your keyboard is properly connected to the computer and to the KVM switch. Check that your keyboard is plugged into the PS/2 keyboard port and not the PS/2 mouse port. Connect your keyboard to the computer directly to verify that it is working. ...

The default password is eight zeros, "00000000".

Press Scroll lock + Scroll Lock + End to reset the switch and it should start responding again. If it does not respond disconnect the mouse for approximately 10 seconds then reconnect it. If it's still not responding reboot the computer. This questions only needs to go under the TK-801R, TK-802...

Unfortunately, you can not turn it off when switching from one PC to another. You can turn it off when operating in auto scan mode only. The command for this is Scroll lock + Scroll lock + B. ...

The User's Guide or Quick Install Guide has a complete list of hotkey commands. You can download the User's Guide and Quick installation guide here: https://www.TRENDnet.com/asp/download_manager/category.asp?iType=29 Hotkey convention: The hotkey notation denotes that you should hit the individua...

Scroll lock + Scroll lock + Up or Down arrows. For a complete list of hotkey commands please consult the user's guide or Quick Install Guide. ...

Only the TK-404KR and TK-204KR support DVI connections.

On the TK-207K the console ports are USB and support standard USB mice and keyboards. All other TRENDnet KVM switches have PS/2 console ports and support standard PS/2 mice and keyboards. ...

You can switch PCs by pressing the Push button on the KVM switch or by using the Hot-Key commands.

Yes, the KVM switch will restore the keyboard settings between computers such as Cap lock, Num key, etc. ...

Yes, you can connect or disconnect the PS/2 cables while the computers are turned on because the KVM switch is Plug-and-Play and Hot-Pluggable....

The TK-802R or TK-1602R requires a power adapter/supply for the OSD to function. It is recommended that you use the included power adapter. ...