Firmware Version: 1.0.0.6
Date: 10/2010
Notes:
- Resolved an issue related to logging out from the Virtual Server page.
- Resolved DHCP reservation issue.
Filename: FW_TWG-BRF114_V1(1.0.0.6).zip
SHA-1 Checksum: 8D84CC5F786C1342F5FD74B31D205F8698B8D745
Date: 7/28/2017
File Size: 620.35 KB
Filename: EN_Spec_TWG-BRF114(V1.0R).pdf
Date: 12/20/2007
File Size: 409.84 KB
Filename: FR_Spec_TWG-BRF114(V1.0R).pdf
Date: 12/20/2007
File Size: 415.00 KB
Filename: GE_Spec_TWG-BRF114(V1.0R).pdf
Date: 12/20/2007
File Size: 416.43 KB
Filename: SP_Spec_TWG-BRF114(V1.0R).pdf
Date: 12/20/2007
File Size: 413.97 KB
Filename: RU_Spec_TWG-BRF114(V1.0R).pdf
Date: 12/20/2007
File Size: 800.64 KB
Filename: EN_QIG_TWG-BRF114.pdf
Date: 11/26/2007
File Size: 639.97 KB
Filename: FR_QIG_TWG-BRF114.pdf
Date: 11/26/2007
File Size: 642.50 KB
Filename: GE_QIG_TWG-BRF114.pdf
Date: 11/26/2007
File Size: 643.33 KB
Filename: PO_QIG_TWG-BRF114.pdf
Date: 9/24/2008
File Size: 491.57 KB
Filename: SP_QIG_TWG-BRF114.pdf
Date: 11/26/2007
File Size: 644.54 KB
Filename: RU_QIG_TWG-BRF114.pdf
Date: 11/26/2007
File Size: 980.15 KB
Filename: UG_TWG-BRF114.pdf
Date: 11/26/2007
File Size: 1.90 MB
JPEG Image
File Size: : 339.13 KB
Date: : 11/26/2007
JPEG Image
File Size: : 268.47 KB
Date: : 11/26/2007
JPEG Image
File Size: : 274.50 KB
Date: : 11/26/2007
JPEG Image
File Size: : 3.25 MB
Date: : 11/26/2007
TIFF Image
File Size: : 2.68 MB
Date: : 11/26/2007
TIFF Image
File Size: : 2.73 MB
Date: : 11/26/2007
Open your web browser and type the IP address of the TWG-BRF114 in the address bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
Put a check mark in the Enable box. Rename the servic...
The MAC Address can be found on a label on the bottom of the router. You can alternately find it by doing the following:
Open your web browser and type the IP address of the TWG-BRF114 in the address bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and pas...
Click Start then click on the Control Panel. For Windows 2000 click on Start, highlight settings then click on the Control Panel.
Double-Click on the Network Connection icon.
Right-Click on the Local Area Connection icon then click on Properties.
Highlight the Internet Protocol (TCP/I...
Open your web browser and type the IP address of the TWG-BRF114 in the address bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
Click on LAN on the left hand side.
Change the IP addre...
The default username & password for the TWG-BRF114 are both (blank). There is no username and password set by default....
The default IP address for the TW100-BRF114U is 192.168.0.1.
Locate the reset button on the back of the TWG-BRF114.
Press and hold in the reset button for approximately 15 seconds. This will reset the unit back to its default configuration.
...
Open your web browser and type the IP address of the TWG-BRF114 in the address bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
Click on Password on the left hand side.
Enter in t...
Note: The default setting of the router is configured for a Cable connection using a Dynamic IP Address.
Open your web browser and type the IP address of the TWG-BRF114 in the address bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and password (blank). ...
Open your web browser and type the IP address of the TWG-BRF114 in the address bar. The default IP address is 192.168.0.1. At the login, enter your username (blank) and password (blank). NOTE: If the Setup Wizard starts, click on Cancel.
Click on WAN Port on the left hand side.
Choose PPPoE f...
Hardware |
Standards | IEEE 802.3, 802.3u and 802.3ab |
Protocols | NAT, PPPoE, HTTP, DHCP, TCP/IP, UDP, PAP, CHAP, RIP1 and DDNS |
Firewall | NAT, Stateful Packet Inspection, Attack Alert Email and Log and Denial of Service |
Security | Access Control |
Local port | 4 x RJ45 10/100/1000Mbps Gigabit Ethernet Auto-MDI/MIDX |
Internet port | 1 x Shielded RJ45 10/100/1000Mbps Gigabit Ethernet Auto-MDI/MIDX |
Reset Button | Resets to Factory Default Settings |
LEDs | Power, Status, Link/Act, 10 ,100 ,1000 LAN and WAN |
Power | DC 12v 800mA External Power Adapter |
Dimensions (LxWxH): | 141 x 100 x 27 mm (5.5x 3.9 x 1.06 inches) |
Weight | 363g (12.8 oz.) |
Temperature | - Operating: 0° to 40° C(32° to 104° F)
- Storage: -10° to 70° C (14° to 158° F)
|
Humidity | - Operating: 0 % ~ 80 % (non-condensing)
- Storage: 0% ~ 95% (non-condensing)
|
Certifications | CE |
|
PACKAGE CONTENTS |
- TWG-BRF114
- Multi-Language Quick install guide
- CD-ROM (User's Guide)
- Power Adapter (12V DC, 800mA)
|
All references to speed are for comparison purposes only. Product specifications, size, and shape are subject to change without notice, and actual product appearance may differ from that depicted herein.