| Standards | - IEEE 802.1d
- IEEE 802.1p
- IEEE 802.1Q
- IEEE 802.1w
- IEEE 802.1X
- IEEE 802.1ab
- IEEE 802.1ax
- IEEE 802.3u
- IEEE 802.3x
- IEEE 802.3z
- IEEE 802.3ab
- IEEE 802.3ad
- IEEE 802.3az
- IEEE 802.3af
- IEEE 802.3at
|
|---|
| Device Interface | - 8 x Gigabit PoE+ ports
- 2 x 100/1000Mbps SFP ports
- 6-pin removable terminal block (primary/RPS power inputs & alarm relay output)
- DIP switches
- LED indicators
- Reset button
|
|---|
| Performance | - Switch fabric: 20Gbps
- RAM buffer: 128MB
- MAC address table: 8K entries
- Jumbo frames: 10KB
- Forwarding rate: 14.88Mpps (64-byte packet size)
|
|---|
| Management | - HTTP web-based GUI
- CLI: Telnet / SSHv2
- SNMP v1, v2c, v3
- SNMP trap (up to 5 receivers)
- RMON groups 1/2/3/9
- Modbus
- Device configuration backup & restore, upgrade firmware, reboot, and reset to default
- Multiple administrative or read-only user accounts
- Enable or disable power saving mode per port
- Static MAC entries
- LLDP (Link layer discovery protocol)
- Topology map
- ONVIF device discovery
- SNTP
- SMTP alert
- Syslog
- Port statistics/utilization
- Traffic monitor
- Port mirror: one to one, many to one
- Storm control: Broadcast, multicast, destination lookup failure (Min. limit: 1pps)
- Loopback detection
- DHCP relay/option 82
- SFP DDMI (Digital Diagnostic Monitoring Interface)
- ERPS (Ethernet Ring Protection Switching) G8032v2
|
|---|
| MIB | - MIB II RFC 1213
- Bridge MIB RFC 1493
- RMON (Group 1,2,3,9) RFC 2819 RFC 1757
|
|---|
| Spanning Tree | - IEEE 802.1d STP (spanning tree protocol)
- IEEE 802.1w RSTP (rapid spanning tree protocol)
- BPDU filter, guard, and root guard
|
|---|
| Link Aggregation | - Static link aggregation and 802.3ad dynamic LACP (Up to 3 groups)
|
|---|
| Quality of Service (QoS) | - 802.1p Class of service (CoS)
- DSCP (Differentiated Services Code Point)
- Bandwidth control per port
- Queue Scheduling: strict priority (SP), weighted round robin (WRR), weighted fair queuing (WFQ)
|
|---|
| VLAN | - 802.1Q tagged VLAN
- MAC-based VLAN
- Protocol VLAN
- Port isolation
- Up to 256 VLAN groups, ID range 1-4094
|
|---|
| Multicast | - IGMP snooping v1, v2, v3
- IGMP querier
- IGMP fast leave
- Up to 256 multicast groups
- Static multicast entries
|
|---|
| Access Control | - 802.1X authentication (Local user database, RADIUS, guest VLAN assignment)
- DHCP snooping/screening
- Trusted host/IP access list for management access
- Port Security/MAC address learning restriction (Up to 100 entries per port)
- Static/dynamic ARP inspection
|
|---|
| ACL | - Source/Destination MAC address
- Source/Destination IP address
- Source Interface
- VLAN ID
- EtherType
- TCP/UDP port 1-65535
|
|---|
| Special Features | - Netlite device discovery and map display in GUI
- Port security: MAC address learning restriction per port
- DHCP relay/option 82 & DHCP server snooping/screening support
- Wide operating temperature range
- Redundant power inputs
- Alarm relay triggered by power failure
- Surge and ESD protection
|
|---|
| Power | - PWR (Primary) terminal input: 24 – 57V DC
- RPS (Redundant) terminal input: 24 – 57V DC
- Compatible power supply: TI-S12024 (120W), TI-S24048 (240W), TI-S48048 (480W) sold separately
- Max. Consumption: 13W (no PoE load), 253W (full PoE load)
|
|---|
| PoE | - PoE budget: 240W@48V DC input, 124W@24V DC input
- 802.3at: Up to 30W per port
- PoE Mode A: Pins 1, 2, 3, and 6 for power
- PoE auto classification
- PoE port priority/power scheduling/PD alive check
- Over current/short circuit protection
|
|---|
| Terminal Block | - Redundant power inputs, alarm relay contact, 6 pin
- Wire range: 0.5 mm² to 2.5 mm²
- Solid wire (AWG): 12-26
- Stranded wire (AWG): 12-26
- Wire strip length: 10-11mm
|
|---|
| DIP Switch | | Switch | Status | Function | | 1 | OFF | Disable alarm relay for PWR power input | | ON | Enable alarm relay for power failure on PWR power input | | 2 | OFF | Disable alarm relay for RPS power input | | ON | Enable alarm relay for power failure on RPS power input | | 3 | OFF | Storm control managed by switch configuration | | ON | Enable storm control (Broadcast and DLF rate set to 300pps) Takes precedence over storm control switch configuration | | 4 | OFF | 802.1p QoS managed by switch configuration | | ON | Enable 802.1p QoS on ports 1 and 2 (Set CoS priority to tag 4 on ports 1 and 2) Takes precedence over 802.1p QoS switch configuration | | 5 | OFF | Port 9 SFP set to Gigabit speed full duplex | | ON | Port 9 SFP set to 100Mbps speed full duplex | | 6 | OFF | Port 10 SFP set to Gigabit speed full duplex | | ON | Port 10 SFP set to 100Mbps speed full duplex |
|
|---|
| Alarm Relay Output | - Relay output with current carrying capacity of 1A, 24V DC
- Short circuit mode when one power source is connected
- Open circuit mode when two power sources are connected
|
|---|
| Enclosure | - IP40 rated metal enclosure
- Fanless passive cooling
- DIN-Rail mount
- Grounding point
- ESD (Ethernet) Protection: 8kV DC
- Surge (Power) Protection: 6kV DC
|
|---|
| MTBF | |
|---|
| Operating Temperature | - -40° – 75° C (-40° – 167° F)
|
|---|
| Operating Humidity | |
|---|
| Dimensions | - 160 x 120 x 50mm (6.3 x 4.72 x 1.97 in.)
|
|---|
| Weight | |
|---|
| Certifications | - CE
- FCC
- Shock (IEC 60068-2-27)
- Freefall (IEC 60068-2-32)
- Vibration (IEC 60068-2-6)
|
|---|
| Warranty | |
|---|
