skip to main content
Click to change country
Search FAQs
Browse by Product
FAQ Home Page > Wireless > Routers > TEW-632BRP
Browse TEW-632BRP Questions
There are 17 questions found in this category:

  1. How do I secure my wireless network?
    WPA(2)-PSK Example Authentication type: WPA PSK/EAP: PSK Cipher Type: TKIP Passphrase: 0123456789abcdef Confirm passphrase: 0123456789abcdef The key must be between 8~63 digits or 64 HEX characters. Step 1 Log into the TEW-632BRP by entering its IP address into a browser. The default IP a...
  2. Can I replace the antenna on the unit with high gain antenna?
    No, you can not replace the antenna on the unit with a high gain antenna.
  3. How do I achieve 300Mbps 802.11n Draft speeds?
    Step 1 Your computer must have a TRENDnet 802.11n wireless adapter installed (e.g. TEW-621PC, TEW-623PI, TEW-624UB). Step 2 Log into the router by entering its IP address into a browser. The default IP address is https://192.168.10.1. The default username is admin with a password of admin. St...
  4. How do I use my router as an Access Point only?
    Step 1 Log into the router by entering its IP address into a browser. The default IP address is https://192.168.10.1. The default username is admin with a password of admin. Step 2 Click on "Main" on the left hand side then click on "LAN&DHCP Server". Step 3 Change the IP Address to be ...
  5. How do I improve my wireless signal?
    Step 1: Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. In an indoor environment try to position the wireless devices so that the signal pas...
  6. How do I change the password on my router?
    Step 1 Log into the TEW-632BRP by entering its IP address into a browser. The default IP address is https://192.168.10.1. The default username and password are both "admin". Step 2 Click on "Main" on the left hand side then click on "Password". ...
  7. I am unable to run the EasyGo setup on my Mac or I receive an error message after running the EasyGo setup CD. What can I do?
    The EasyGo setup will only work on a Windows PC. If you want to setup the router from a non-Windows PC or if you receive an error message, Step 1 Connect an Ethernet cable from your modem to the WAN port on the router. Step 2 Connect a second Ethernet cable from your computer to one of the 4 L...
  8. I receive an elevation error when I run the EasyGo Setup on my Windows Vista PC. What can I do?
    Step 1: Click the Microsoft Windows icon and then click "Computer". Step 2: Right click on the CD-ROM/DVD-ROM drive and click Open. Step 3: Right click on autorun.exe and click Run as administrator. Step 4: Repeat the steps in the QIG. ...
  9. I have connected my WPS enable computer to the TEW-632BRP but how do I connect a non WPS wireless computer to it?
    You would connect to it like a standard wireless network. You will be prompted for the key that was generated during the WPS connection process. You can verify the key by following the steps below: Step 1 Log into the router by entering its IP address into a browser. The default IP address is htt...
  10. How do I connect to my TEW-632BRP using WPS (WiFi Protected Setup)?
    Step 1 Press the WPS button located on the right side of the TEW-632BRP. The button will start to blink indicating that it is ready for a WPS enabled computer to connect. Step 2 Press the PBC (Push Button Connect) button in your wireless adapter's utility. Example using a TEW-621PC wireles...
  11. How do I forward ports, create pin holes in the firewall or create Virtual Servers in my TEW-632BRP?
    For Well Known Ports Log into the router by entering its IP address into a browser. The default IP address is https://192.168.10.1. At the login, enter your username (admin) and password (admin). Click on "Cancel" if the Setup Wizard comes up. Click on "Access" on the left hand side. ...
  12. How do I secure my wireless network?
    WPA-PSK/WPA2-PSK Example Authentication type:WPA PSK/EAP: PSK Cipher Type: TKIP Passphrase: 0123456789abcdef Confirm passphrase: 0123456789abcdef The key must be between 8~63 digits or 64 HEX characters. Step 1 Log into the TEW-632BRP by entering its IP address into a browser. The defau...
  13. How do I log into the TEW-632BRP to change its settings?
    Step 1 Log into the TEW-632BRP by entering its IP address into a browser. The default IP address is https://192.168.10.1. The default username and password are both "admin". ...
  14. How do I change the IP address of my TEW-632BRP?
    Step 1 Log into the TEW-632BRP by entering its IP address into a browser. The default IP address is https://192.168.10.1. The default username and password are both "admin". Step 2 Click "Main" on the left hand side then click on "LAN & DHCP Server". Step 3 Enter in the new value for IP Add...
  15. What is the default IP address of my TEW-632BRP?
    The default IP address is https://192.168.10.1. The default username and password are both "admin". ...
  16. How do I upgrade the firmware on my TEW-632BRP?
    Go to our website and check for available firmware updates here. https://www.TRENDnet.com/support/supportdetail.asp?prod=140_TEW-632BRP#tabs-solution01 > Firmware upgrade failure may permanently damage the unit and causing it not to function. If the issues in the "Release Notes" do not addre...
  17. What can I do if I forgot my password or want to reset back to factory defaults?
    Power up the TEW-632BRP, wait 30 seconds for it to boot up, press and hold the reset button for 15 seconds and then release it. Do not press and hold the reset button for more than 30 seconds. ...